Resins for Trenchless Pipe and Sewer Rehabilitation
For trenchless pipe and sewer rehabilitation, you will find the right resin here. High quality and a range of pot lives make your job easier. Always remember to wear personal protective equipment and be careful during application. Please contact us if you have any queries. We offer the following systems:
>> WILLPUR WS (polyurethane resin for drainage shafts)
>> WILLKAT SL/PL (silicate resin for short liner renovation)
>> CarboLith PL (silicate resin for short liner renovation)
>> Sikotec 3P (silicate resin for short liner renovation)
WILLKAT® PL 2K Summer Two-Component Resin, Non-Foaming, Elasticised
WILLKAT® PL 2K Summer is a non-foaming, elastified two-component resin. It adheres very well to damp surfaces and is used for the renovation and sealing of sewers and pipes using the short liner method or top hat system. DIBt approval: Z-42.3-523. Different sizes of packaging are available for both components: in a metal canister or as a 1 l PE bottle. Technical data Note: The mixing ratio A to B = 1:2 is based on volume, not weight. Because the two components have different densities, their package weights differ. The packaging units are designed so that mixing complete containers automatically provides the correct volume ratio. Mixing ratio A to B: 1:2 Potlife (spreading time) at 20°C [min]: 16 Setting time at 20°C [min]: 27 Demould time at 20°C [min]: 90 Processing PE bottles: Component A is completely filled into the component B bottle. After closing the bottle, both components are mixed intensively by shaking the bottle until a streak-free product is obtained.Canister: The A component is intensively mixed with twice the volume of the B component for two minutes. Packaging Units WILLKAT® PL 2K Summer PE-Bottle 1l: Comp. A 250 ml or 335 ml PE-Bottle 1l: Comp. B 500 ml or 65 ml Metal can 10 l: Comp. A 14 kg Metal can 20 l: Comp. B 21 kg Bundle A+B in metal cans 10 l + 20 l
WILLPUR® WS Two-Component Polyurethane Resin With Short Reaction Time, 12 Pcs.
WILLPUR® WS is a two-component polyurethane resin with short reaction time and high final strength. It is suitable for manhole and robot rehabilitation, for sealing and consolidating in water-bearing zones, especially against water under pressure. The injection resin is free of CFCs and halogens and foams slightly on contact with water. Application: Stopping unexpected water inflows, consolidating unstable soils with disturbed geology, stopping water seepage and sealing shafts, underground structures, dams and tunnel linings. Scope of delivery 1 carton of 12 double chamber cartridges with 400ml, each containing comp. A 200 ml + comp. B. 200 ml.
Carbolith PL Silicate Resin, set includes all three components A, B, C
Get your 3C silicate resin in a practical set - Carbolith PL is a proven system for professional short liner renovation, consisting of the components resin (A), hardener (B) and catalyst (C) in the following quantities: 1 x CarbolithPL component A, 23.8 kg (item no. 211-100-030) = resin / water glass 2 x CarbolithPL component B, 18 kg (item no. 211-100-010) = hardener 1 x CarbolithPL component C, 1 kg (item no. 211-100-040) = catalyst Our set saves you from having to convert the chemical mixing ratios. The necessary and suitable constellation of this carbolith resin is already ideally put together in this set and is therefore ready for immediate use for pipe renovation. Suitable for bonding partial inliners (short liners) during sewer rehabilitation. General building authority approval: DIBt no. Z-42.3-383 Safety and hazard information for the resin included: contains diisocyanates (only component C) CLP classification: GHS05 (component C), GHS07 (component A, B, C), GHS08 (component B, C) UN number: not regulated (component A, B), 3267 (component C) In the "Downloads" tab you will find a separate safety data sheet for each component, which should be observed.
3P® Resin Summer (S1) 1 unit: 30 liters = 40.5 kg, comp. A + B
SIKOTEC 3P®S1 - High Quality Silicate Resin with longer pot life 1 unit: 30 liters = 40.5 kg 20 l resin S1 (comp. B) and 10 l Water glass, Betol 3P (Comp. A) Customs tariff no.: Comp. B - resin: 39095090 Customs tariff no.: Comp. A - hardener: 28391900 Pot life: 32 minutes Curing time: 180 - 240 min Mixing ratio: A:B= 1:2 Storage temperature: 0 - 30°C Nominal size: DN 100 - 700 DIBt approval: Z-42.3-326 Safety note: component A contains diisocyanates: no CLP classification: GHS05 UN number: not regulated Please read the full >> Safety data sheet Safety note: component B (S1) contains diisocyanates: yes CLP classification: GHS07, GHS08 UN number: not regulated Please read the full >> Safety data sheet
WILLKAT® PL 2K Winter Two-Component Resin, Non-Foaming, Elasticised
WILLKAT® PL 2K Winter is a non-foaming, elastified two-component resin. It adheres very well to damp surfaces and is used for the renovation and sealing of sewers and pipes using the short liner method or top hat system. DIBt approval: Z-42.3-523. Different sizes of packaging are available for both components: in a metal canister or as a 1 l PE bottle. Technical data Mixing ratio A to B: 1:2 Potlife (spreading time) at 20°C [min]: 15 Setting time at 20°C [min]: 25 Demould time at 20°C [min]: 60 Processing PE bottles: Component A is completely filled into the component B bottle. After closing the bottle, both components are mixed intensively by shaking the bottle until a streak-free product is obtained.Canister: The A component is intensively mixed with twice the volume of the B component for two minutes. Packaging Units WILLKAT® PL 2K Winter PE-Bottle 1l: Comp. A 250 ml or 335 ml PE-Bottle 1l: Comp. B 500 ml or 65 ml Metal can 10 l: Comp. A 14 kg Metal can 20 l: Comp. B 21 kg Bundle A+B in metal cans 10 l + 20 l
WILLPUR® WS HF Two-Component Injection Resin High Foaming, Instant Setting, 12 Pcs.
WILLPUR® WS HF is an instant setting, high foaming two-component injection resin. The polyurethane system is suitable for shaft and robot rehabilitation, for sealing and consolidating in water-bearing zones, especially against pressing water. The injection resin is free of CFCs and halogens. Field of application: Stopping unexpected water inflows, for consolidating unstable soils with disturbed geology, stopping water seepage and sealing shafts, underground structures, dams and tunnel linings. Reaction data Reaction profile (cartridge application) at 20 °C Start time: approx. 10 s Curing time: approx. 33 s Reaction temperature: approx. 85 °C Expansion factor: approx. 30Reaction profile (laboratory values)Start time: 5-7 s Setting time (gel time): 13-17 s Tack-free: 18-20 s Scope of delivery WILLPUR® WS HF 1 box of 12 double chamber cartridges, each with 400ml, containing comp. A 200 ml + comp. B. 200 ml. Processing Both components are processed in a volume ratio of 1:1 using a two-component pump or a two-component cartridge dispenser. The components are intimately mixed while passing through a static mixer and, if necessary, injected via a packer.
3P® Resin Winter (W1) 1 unit: 30 liters = 40.5 kg, comp. A + B
SIKOTEC 3P® W1 silicate winter resin is our all-rounder with a medium pot life. Each order is a coordinated unit consisting of components A and B in the approved mixing ratio. The delivery quantity is a total of 30 liters (40.5 kg).We offer two versions, which only differ in the container size of component B. The total amount is the same! Please choose as preferred: 1x 20 liter canister (B) or 2x 10 liter canister (B) for easier handling when pouring Characteristics: Pot life: 17 minutes Curing time: 90 - 120 min Mixing ratio: A:B= 1:2 Storage temperature: 0 - 30°C Nominal size: DN 100 - 700 DIBt approval: Z-42.3-326 Customs tariff no.: Comp. B - resin: 39095090Customs tariff no.: Comp. A - hardener: 28391900 Safety note: component A contains diisocyanates: no CLP classification: GHS05 UN number: not regulated Please read the full >> Safety data sheet Safety note: component B (W1) contains diisocyanates: yes CLP classification: GHS07, GHS08 UN number: not regulated Please read the full >> Safety data sheet
3P® Resin Turbo (W01) 1 unit: 30 liters = 39.5 kg, comp. A + B
SIKOTEC 3P®W01 - Turbo - Silicate Resin for faster results1 unit: 30 liters = 39.5 kg20 l resin W01 (comp. B) and 10 lWater glass, Betol 3P (Comp. A)Customs tariff no.: Comp. B - resin: 39095090Customs tariff no.: Comp. A - hardener: 28391900When it has to be fast: Pot life: 7 minutes Curing time: 45 - 60 min Mixing ratio: A:B= 1:2 Storage temperature: 0 - 30°C Nominal size: DN 100 - 700 DIBt approval: Z-42.3-326 Safety note: component A contains diisocyanates: no CLP classification: GHS05 UN number: not regulated Please read the full >> Safety data sheet Safety note: component B (W01) contains diisocyanates: yes CLP classification: GHS07, GHS08 UN number: not regulated Please read the full >> Safety data sheet
Carbolith PL Silicate Resin, B component, Hardener 18 kg
B-Component / Hardener for Carbolith PL Silicate Resin System. One bucket with 18 kg Safety and hazard information contains diisocyanates CLP Classification: GHS07, GHS08 UN number: not regulated Please observe the >> safety data sheet
Carbolith PL Silicate Resin, Component A, Water Glass, 23.8 kg
Component A supplies the water glass for the CarbolithPL resin 3K system 23,8 kg bucket, corresponds to approx. 18 liters Produced in EU. General building authority approval: DIBt no. Z-42.3-383 Quality resin for high and low processing temperatures. Curing can be individually controlled with this 3K system. Non-foaming, elasticized three-component resin with good adhesion even on damp surfaces. Suitable for bonding partial inliners (short liners) during sewer rehabilitation. Safety and hazard information contains no diisocyanates CLP Classification: GHS07 UN number: not regulated Please observe the >> safety data sheet to protect yourself and others!
Carbolith PL Silicate Resin Catalyst, C-Component, 1 kg
Carbolith C-Component Resin Catalyst 1 Liter Package, 1 kg Safety and hazard information: contains no diisocyanates CLP classification: GHS05, GHS07, GHS08 UN number: 3267 Please note the >> safety data sheet
Quadromixer 08-24 With Tip
Quadromixer 08-24 with tip, which is screwed onto a cartridge of resin for mixing two components.
Impact Aid For Lamella Impact Packer
Impact aid for lamella impact packer.
Lamella Impact Packer 14x95
Lamella impact packer 14x95 - injection aid for injecting the resins.
2K Squeezing Device For Manual Squeezing Of 400 ml Cartridges
2K squeezing device for manual squeezing of the cartridges, for 400 ml cartridges MV 1:1.
2C Squeezer For Squeezing Out 400 ml Cartridges With Compressed Air
2C squeezer for squeezing out the cartridges with compressed air, for 400 ml cartridges MV 1:1.
WILLKAT® PL 3K Non-Foaming Elastified Three-Component Resin
WILLKAT® PL 3K is a non-foaming elastified three-component resin with good adhesion even to damp surfaces for the renovation and sealing of sewers and pipes using the short liner method in sewer rehabilitation. DIBt approval: Z-42.3-523. Technical data Mixing ratio A:B:C 100:200:1 Pot life (spreadability) at 20°C [min]: 15 Application time at 20°C [min]: 25 Demoulding time at 20°C [min]: 60 Application The three-component system can be adjusted to the respective requirements with regard to temperature, size of the short liner and required application time by specific dosage of the C component. Stir component C before use and mix it into the A-component in a suitable quantity. Stir this mixture intensively for two minutes with twice the volume of the B component. Packaging Units WILLKAT® PL 3K Metal can 20 l: Comp. A 28 kg Metal can 20 l: Comp. B 21 kg Metal can 1 l: Comp. C 1 kg Bundle A+2xB+C in metal cans 20 l + 2x20 l + 1 l
WILLKAT® PL 2K Slow Two-Component Resin, Non-Foaming, Elasticised
WILLKAT® PL 2K Slow is a non-foaming, elastified two-component resin. It adheres very well to damp surfaces and is used for the renovation and sealing of sewers and pipes using the short liner method or top hat system. DIBt approval: Z-42.3-523. Different sizes of packaging are available for both components: in a metal canister or as a 1 l PE bottle. Technical data Mixing ratio A to B: 1:2 Potlife (spreading time) at 20°C [min]: 18 Setting time at 20°C [min]: 28 Demould time at 20°C [min]: 120 Processing PE bottles: Component A is completely filled into the component B bottle. After closing the bottle, both components are mixed intensively by shaking the bottle until a streak-free product is obtained.Canister: The A component is intensively mixed with twice the volume of the B component for two minutes. Packaging Units WILLKAT® PL 2K Slow PE-Bottle 1l: Comp. A 250 ml or 335 ml PE-Bottle 1l: Comp. B 500 ml or 65 ml Metal can 10 l: Comp. A 14 kg Metal can 20 l: Comp. B 21 kg Bundle A+B in metal cans 10 l + 20 l
WILLKAT® PL 2K Fast Two-Component Resin, Non-Foaming, Elasticised
WILLKAT® PL 2K Fast is a non-foaming, elastified two-component resin. It adheres very well to damp surfaces and is used for the renovation and sealing of sewers and pipes using the short liner method or top hat system. DIBt approval: Z-42.3-523. Different sizes of packaging are available for both components: in a metal canister or as a 1 l PE bottle. Technical data Mixing ratio A to B: 1:2 Potlife (spreading time) at 20°C [min]: 9 Setting time at 20°C [min]: 13 Demould time at 20°C [min]: 50 Processing PE bottles: Component A is completely filled into the component B bottle. After closing the bottle, both components are mixed intensively by shaking the bottle until a streak-free product is obtained.Canister: The A component is intensively mixed with twice the volume of the B component for two minutes. Packaging Units WILLKAT® PL 2K Fast PE-Bottle 1l: Comp. A 250 ml or 335 ml PE-Bottle 1l: Comp. B 500 ml or 65 ml Metal can 10 l: Comp. A 14 kg Metal can 20 l: Comp. B 21 kg Bundle A+B in metal cans 10 l + 20 l
WILLKAT® PL 2K Fast Plus Two-Component Resin, Non-Foaming, Elasticised
WILLKAT® PL 2K Fast Plus is a non-foaming, elastified two-component resin. It adheres very well to damp surfaces and is used for the renovation and sealing of sewers and pipes using the short liner method or top hat system. DIBt approval: Z-42.3-523. Different sizes of packaging are available for both components: in a metal canister or as a 1 l PE bottle. Technical data Mixing ratio A to B: 1:2 Potlife (spreading time) at 20°C [min]: 7 Setting time at 20°C [min]: 10 Demould time at 20°C [min]: 55 Processing PE bottles: Component A is completely filled into the component B bottle. After closing the bottle, both components are mixed intensively by shaking the bottle until a streak-free product is obtained.Canister: The A component is intensively mixed with twice the volume of the B component for two minutes. Packaging Units WILLKAT® PL 2K Fast Plus PE-Bottle 1l: Comp. A 250 ml or 335 ml PE-Bottle 1l: Comp. B 500 ml or 65 ml Metal can 10 l: Comp. A 14 kg Metal can 20 l: Comp. B 21 kg Bundle A+B in metal cans 10 l + 20 l
WILLKAT® SL 2K Summer Two-Component Resin In Plastic Containers
WILLKAT® SL 2K Summer is a non-foaming, elastified two-component resin, packaged in plastic containers. It adheres very well to damp surfaces and is used for sewer rehabilitation and the sealing of sewers and pipes using the short liner method or top hat system. DIBt approval: Z-42.3-523. The two-component resin consists of two components A and B, which are used in a mixing ratio of 1:2. WILLKAT SL is catalysed by the B component. The A component is a modified polyisocyanate. Technical data Mixing ratio A to B: 1:2 Potlife (spreading time) at 20°C [min]: 18 Setting time at 20°C [min]: 28 Demould time at 20°C [min]: 120 Processing The A-component is intensively mixed with twice the volume of the B-component for two minutes. Packaging Units WILLKAT® SL 2K Summer Plastic Container 10 l: Comp. A 13 kg or Comp. B 10 kg Plastic Container 20 l: Comp. B 20 kg Bundle with Comp. A + B in plastic containers 10 l + 20 l
WILLKAT® SL 2K Winter Two-Component Resin In Plastic Containers
WILLKAT® SL 2K Winter is a non-foaming, elastified two-component resin, packaged in plastic containers. It adheres very well to damp surfaces and is used for sewer rehabilitation and the sealing of sewers and pipes using the short liner method or top hat system. DIBt approval: Z-42.3-523. The two-component resin consists of two components A and B, which are used in a mixing ratio of 1:2. WILLKAT SL is catalysed by the B component. The A component is a modified polyisocyanate. Technical data Mixing ratio A to B: 1:2 Potlife (spreading time) at 20°C [min]: 9 Setting time at 20°C [min]: 13 Demould time at 20°C [min]: 50 Processing The A-component is intensively mixed with twice the volume of the B-component for two minutes. Packaging Units WILLKAT® SL 2K Winter Plastic Container 10 l: Comp. A 13 kg or Comp. B 10 kg Plastic Container 20 l: Comp. B 20 kg Bundle with Comp. A + B in plastic containers 10 l + 20 l
WILLKAT® SL 2K Fast Two-Component Resin In Plastic Containers
WILLKAT® SL 2K Fast is a non-foaming, elastified two-component resin, packaged in plastic containers. It adheres very well to damp surfaces and is used for sewer rehabilitation and the sealing of sewers and pipes using the short liner method or top hat system. DIBt approval: Z-42.3-523. The two-component resin consists of two components A and B, which are used in a mixing ratio of 1:2. WILLKAT SL is catalysed by the B component. The A component is a modified polyisocyanate. Technical data Mixing ratio A to B: 1:2 Potlife (spreading time) at 20°C [min]: 4 Setting time at 20°C [min]: 7 Demould time at 20°C [min]: 30 Processing The A-component is intensively mixed with twice the volume of the B-component for two minutes. Packaging Units WILLKAT® SL 2K Fast Plastic Container 10 l: Comp. A 13 kg or Comp. B 10 kg Plastic Container 20 l: Comp. B 20 kg Bundle with Comp. A + B in plastic containers 10 l + 20 l